3 steps windlass rod tourniquet

How to Use a Combat Application Tourniquet (CAT) : 8 Steps

Step 5: Twist the Windlass Rod NO MORE THAN 3 TIMES, Then Insert It Into the Windlass Clip.

Windlass Tourniquet: A windlass tourniquet uses a rod to help stop the blood supply. ... 3. Tourniquets are primarily designed for use on limbs ...

Application of a C.A.T. Tourniquet (3 of 9). Step 3. Adhere the band around the ... Lock the windlass rod in place in the windlass clip. Bleeding is now ...

Twist the windlass rod until the bleeding is controlled. The tourniquet should be tight enough to stop all circulation to the injured limb and control ...

• Twisting the windlass rod more than 3 times may cause it to break. • If you can twist the windlass rod more than 3 times, repeat steps 2-4 and pull the Omni-.

Bleeding Control Skill Stations

Note: The tourniquet application steps described below ... For added security and always before moving the patient, the provider secures the windlass rod with the ...

This is a critical step for proper tourniquet application and results in fewer windlass rotations required to reach occlusion. 3) Rugged Buckle. Engineered to ...

Secure the windlass to keep the tourniquet tight and in place. Note the time – as best you can – of when the tourniquet was applied, some tourniquets may have a ...

A tourniquet requires some form of mechanical assistance such as a windlass rod ... If the rescuer has to turn the rod more than 3—4 times, then ...

Take any of the left over tail of the band and secure it in the windlass clip. Then secure the tail and the windlass rod with the securing strap ...

Home - Stop the Bleed

Stop the Bleed Step 3. Twist the windlass rod tightly. Secure the Tourniquet. Secure the windlass rod in the ...

STEP 3: TWIST WINDLASS (ROD) EITHER WAY UNTIL BLEEDING STOPS. LOCK INTO CARABINER. Additional Trauma Steps: Run your hands over victim's full body, checking ...

... rod (the windlass) that you can twist to tighten the strap. Some of the most common windlass-style tourniquets include the Combat ...

3. Position the C-A-T above the wound; leave at least 2 inches of ... Twist the Windlass Rod until the bleeding stops. When the tactical ...

STEP 3. Twist the rod until bleeding has stopped. Also check for distal pulse beneath the tourniquet near the wound,this should disappear.

Life-Threatening Bleeding + Tourniquet Application Kit

... Tourniquet with windlass rod and student First Aid Training Pack. The First ... (3) · Life-Threatening Bleeding + Tourniquet Application Kit · $31.95. Reviews. The ...

Step 3 - Coagulation ... (4) Lock the windlass rod in place with the clip. C-A-T Tourniquet Use. 68W Combat Medic. Page 27. 10/3/2010. 27.

WINDLASS ROD - Increased diameter, enhanced strength, aggressive ribbing improves grip. 3. WINDLASS CLIP - Bilateral bevelled entry, rapid windlass lock ...

The next step is to grasp the backplate and windlass rod in your hand (this is what you will slide underneath the back of the knee first) and ...

This tourniquet's tightening strap is secured to the windlass wand at a single ring point for super fast tightening. Hook-and-loop backing on the...(25349)

How to Apply a Tourniquet

... tourniquet, including the windlass rod and strap. This tourniquet ... Unwrapping one end of the tourniquet, hold it against the body about 3 ...

C•A•T Resources is the inventor and exclusive manufacturer of the Combat Application Tourniquet ... Windlass Rod. Increased diameter, enhanced strength, ...

TWIST the windlass rod until bleeding has stopped (complete steps. 1-6 in under 1 min). LOCK the windlass rod in place with the windlass clip.

Step 2: Twist the Windlass Rod™ until the bleeding stops. Step 3: Secure the rod and band with the Windlass Strap™M. Another critical design characteristic is ...

Step 5: Tighten the Tourniquet. Tighten the tourniquet around the limb by twisting the windlass. Keep an eye on the bleeding and take note of ...